HOME PAGE                ABOUT US          PRIVACY        CONTACT US


Simple, Fast, Free Estimates!
No Obligation, Find Out How Much You Can Save !


    


...........................................................................




 

 

Thank you for visiting our remodeling contractors website.

   Our remodeling contractors estimate general contractor website is designed exclusively for the homeowner and/or renter to get their job done efficiently and in a timely manner.

  We are dedicated to giving you an easy estimate request form for your remodeling project and following up with prompt and courteous service. We believe that between the customers request and our contractors skill your home improvement project will be a wonderful and delightful experience.

  Fill out the easy form and give us an idea of the project you wish to complete and you will receive an estimate from a qualified and licensed contractor. The benefit of a licensed contractor gives you assurance that your project is in capable hands and the job will be done right from start to finish.



Bathroom Trivia

A bathroom is a room that may have different functions depending on the cultural context it is used in.

In its literal sense it means 'a room with a bath', but as bathtubs have partly made way for showers and steam showers, the more general sense of 'a room where one bathes' makes more sense. There can be just a shower or just a bathtub or both, sometimes combined and sometimes separate (in which case the bathtub may have a second shower). Usually, it also contains a handbasin or sink and often also a toilet. In the USA, 'bathroom' commonly means 'a room containing a toilet' (in other countries this is usually called 'toilet' or alternatively 'water closet' (or 'WC'), or 'lavatory'). For this interpretation of the word see bathroom (American). If a bathroom facility is attached to a bedroom it is often known as an en-suite or if it's attached to a master bedroom it's known as a master bathroom.

A half (1/2) bath contains a toilet and a handbasin (lavatory). A 3/4 bath contains a toilet, a handbasin (lavatory) and a shower. A full bath contains a toilet, a handbasin (lavatory) and a bathtub.

  For information and articles about contractor laws and licensing we have included a link for your convenience. To find out more, simply click on the corresponding state you wish to obtain information from. - Home improvement contractor info

Additional information and resources:

Read Home Decorating Articles - We have included a great resource link for you to get ideas about designing to compliment any home improvement project. The link will open in a new window so you may keep our estimate form open for easy access.

Find Decorating Pictures - Finally...a source for interior decorating and gardening pictures! A giant selection of home and garden, and interior decorating from a great website that will give you many ideas about updating your home with an array of well thought ideas. Link opens in new window so you may return for an estimate.




Design considerations

The design of a bathroom must account for the use of both hot and cold water, in significant quantities, for cleaning the human body. Disposal of the water usually leads to a sewer or septic tank. Water may be splashed on the walls and floor and hot humid air may cause condensation on cold surfaces. From a decorating point of view the bathroom presents a challenge. Ceiling, wall and floor materials and coverings should be impervious to water and readily and easily cleaned. The use of ceramic or glass, as well as smooth plastic materials, is common in bathrooms for their ease of cleaning. However, such surfaces are often cold to the touch and so water-resistant bath mats or even bathroom carpets may be used on the floor to make the room more comfortable. Alternatively, the floor may be heated, possibly by startegically placing heater conduits close to the surface.

Electrical appliances, such as lights, heaters and heated towel rails generally need to be installed as fixtures, with permanent connections rather than plugs and sockets. This minimises the risk of electric shock. Ground-fault circuit interruptor electrical sockets can reduce the risk of electric shock, and are required for bathroom socket installation by electrical and building codes in the United States and Canada. In some countries, such as the UK, only special sockets suitable for electric shavers are permitted in bathrooms, and are labelled as such.

Bathrooms can also be a source of decorative inspiration. One can easily decorate the bathroom by choosing shower curtains or cubicles to match a theme.




Home Improvement Information

Removing Your Old Wood Double Hung Windows


Last week I told you how to measure your wood window openings to properly order your new vinyl replacement windows. This week I'm going to explain how to remove your old windows. The vast majority of wood sash double hung windows in America have the same specifications. Starting from inside the house and working out, you have a wood stop approximately 3/8" X 3/8". Then comes the lower sash (the sash is the piece of glass and surrounding wood frame). Then you have another wood stop (called a parting bead) between the lower sash and upper sash. This stop is approx. 1/4" X 1/2". Then you have the upper sash, and finally, the outside wood stop (called a blind stop) that is approx. 1/2" X 3/4".

Before beginning, be sure to wear safety glasses and gloves. The safety glasses will protect your eyes from debris, and the gloves help avoid splinters. The inside stop needs to be removed first. Try not to damage these,they will be re-installed after the replacement windows are put in. If you should happen to crack the old stops, you can take a piece to a hardware store or molding store to get replacement wood stops. If the stops have been painted to blend into the surrounding trim or wall, you need to put a flat screwdriver or putty knife into the indented area that separates the stop from the surrounding area. Drag the blade from top to bottom to chip away the paint. Then put a stiff blade putty knife into this seam and pry the stop away from the frame. Start in the middle of the stop where there is the most flexibility. Work the putty knife from the middle to the top, then from the middle to the bottom. The number of nails that were used to install the stop will determine how difficult removal will be. I have seen some stops that have just 3 nails, while others have had 6. Most of the time there will be stops around all four sides of the opening, but I have seen some openings that didn't have a top stop, and others that had no bottom stop.

After the inside stops have been removed, you should be able to pull the lower sash out. If the windows were painted shut at some time, you might have to pry the area where the lock is located to separate the sashes. Now, once you get the lower sash out, it will still be attached to the cords that hold the window up when you raise it. Take a pair of tin snips and cut the cords while maintaining tension on them. The cords will recoil back into the assemblies. Take the lower sash and set it aside.

Next,we need to remove the middle stop, or parting bead. This piece is going to be thrown away, so you don't have to be careful when removing this piece. The parting bead will be on top and along both sides. It's never on the bottom. Take a screwdriver and tap it into the groove between the side frame and parting bead. Pry out. The bead is nailed into a recessed groove. When all of the parting bead is out, the upper sash will come out. If it's painted to the outside stop, CAREFULLY pry the sash from the outside stop with a stiff putty knife. You want to avoid damaging the outside stop. Remove the upper sash the same way you did the lower sash, cutting the cords under tension.

At this point,you should have the inside stops removed and set aside to be installed later, both sashes removed, the middle stop or parting bead removed and discarded,and the outside blind stop left in place undisturbed. Check to make sure there are no obstructions in the opening such as nails,the metal tab at the bottom for holding in the old screen, etc. The final step is to take a stiff putty knife and scrape the inside face of the outside blind stops to get rid of any old caulking. This is the surface that the replacement windows are going to rest against, and we are going to want this area as smooth as possible. Clean up all loose debris from the opening, and you are now ready to install your replacement windows. That will be our topic for next weeks article...

John Rocco has been installing replacement windows since 1978. To learn more, visit How To Install Windows


MORE RESOURCES:
You told us your 2009 resolutions, from replacing electrical outlets to overhauling landscaping. We help you get the job done

One look at the dilapidated 1926 foursquare—smack in the middle of beach-condo country—sealed the deal for this couple.

A from-scratch kitchen with every convenience and finely crafted woodwork is a natural fit for a Craftsman-style home

Fancy fireplace fronts. The Victorians used them to improve the look of their hearths in the off-season, but you can put them to work today to upgrade your interior rooms year-round

Ever wonder what's inside those beautiful city rowhouses? Here's a glimpse of a century-old Renaissance Revival—TOH TV's new project—filled with well-preserved details

Buried by a blizzard? Follow our tips for digging out

Here at This Old House, we're big fans of DIY builders. But little did we know that the tools of the trade—band saws, wood rasps, belt sanders, Dremels—could be used to build dessert

We've had a hive of bees move into a very old olive tree in our front yard. I really don't want to do them any harm, as I understand bees are suffering from hive collapse. But, I do have concerns regarding bite allergies. Is there any way to get the bees to leave voluntarily?

home   |   site map
  ©  Copyright 2003-2006. All rights reserved.    Powered by   HostGator.com    Remodeling Contractors Estimate Form    Do it yourself